How to set up and fluff a flocked tree

A flocked tree looks flat and thin when it comes out of the box, and fluffing is what turns it into the tree in the picture. Set aside an hour, put down an old sheet, and work from the bottom up.

Before you open the box

Pick the spot first, because a fluffed 7.5 ft tree is awkward to move. The Best Choice Products tree is listed at 30.5 lb and the Hykolity at 38.1 lb, so carry the box to the room before you open it.

Measure the ceiling and the floor while the room is still clear. Our guide to choosing the right tree size explains the 6 to 12 inches you want above the topper and why the width at the base matters.

Then gather a few things. Most of the white that ends up on the rug comes off in these first hours, so a little preparation saves a lot of cleanup.

  • An old sheet or drop cloth wider than the base of the tree
  • Gloves, since flocking clings to bare hands and cut tips can scratch
  • Long sleeves you don’t mind getting white
  • A vacuum with a low setting and the beater bar switched off
  • A sturdy step stool for the top section

Stacking the sections

All six trees in our lineup use hinged branches, fixed to the pole and folded up for the box. You lift each section into place and the branches drop down, with no loose branches to hook into numbered slots.

Best Choice Products describes a three-step assembly for its 7.5 ft tree. You open out the metal stand, stack the sections from the largest to the smallest, then fluff.

  1. Open the stand fully and lock it as the manual shows before any weight goes on
  2. Seat the bottom section and check from two sides that it stands straight
  3. Add the middle section, then the top, pushing each one fully home
  4. On a pre-lit tree, join the plugs between sections as the manual describes
  5. Plug in once to see that every section lights before you start shaping

That last check saves a lot of frustration. Owners of several pre-lit flocked trees report sections that stop working, and a dark section is far easier to sort out before an hour of shaping goes in around it.

The National Tree Company 3 ft tabletop tree skips most of this. It comes in one piece on a metal plate base, so you arrange the branches and plug it in.

How to fluff, branch by branch

Fluffing means bending every tip out of its folded position so the tree fills in. It takes longer than stacking, and it decides whether the tree looks full or sparse.

Some people fluff each section as they stack it, since the lower tiers are easier to reach before the upper ones hang over them. Either order works, as long as you start at the bottom.

  1. Start at the branch nearest the pole and work outward to the end
  2. Separate the tips on each branch, spreading some up, some level and some down
  3. Turn the end tip so it points straight out and hides the branch stem
  4. Fan a few inner tips toward the pole to fill the dark center
  5. Step back every few branches and look at the shape from across the room

The last step is easy to skip. A tree shaped from arm’s length can look even up close and patchy from the sofa, so check it from the places where you will sit.

On a pre-lit tree, shape around the wires instead of pulling them. Bulbs tucked inside the branches give depth, and a bulb dragged out to the tip can work loose in its socket.

How long shaping takes

Only National Tree Company gives times. It says to allow about 30 minutes for shaping the Acacia Slim and 45 to 60 minutes for the Wintry Pine, which has pine cones and berry clusters to work around.

TreeBranch tipsShaping time
Best Choice Products 7.5 ft1,346Not stated
Yaheetech 7.5 ft unlit1,284Not stated
Hykolity 7.5 ft1,446Not stated
National Tree Acacia Slim641About 30 minutes (maker)
National Tree 3 ft mini198Arrange the branches and plug in
National Tree Wintry Pine83145 to 60 minutes (maker)

The three full trees carry far more tips than the Wintry Pine, so expect them to take at least as long. Our comparison table puts every tree’s numbers side by side.

Filling gaps after fluffing

Some gaps are normal. Owners of the Yaheetech unlit tree mention gaps that stay after fluffing, and a few say branches came off in their hands, so bend tips gently and never yank a branch at the hinge.

Before you blame the tree, try these fixes in order. Most thin spots come from tips left pointing the same way.

  • Turn the tree so the thinnest side faces the wall or a corner
  • Re-bend the tips beside the gap so they reach across it
  • Lift a drooping branch to the same angle as its neighbors
  • Fill a stubborn hole with a large ornament, a pick or a loop of ribbon

A branch that breaks off at the hinge is a fault, not a fluffing problem. Contact the seller while you are still inside the return window.

Keeping the flocking on the branches

Every flocked tree sheds, and most of it happens during unboxing and fluffing. Gloves, the sheet and a gentle hand keep the loss down, and shedding slows once the tree is standing.

When you finish, fold the sheet inward to trap the fluff and shake it outdoors, then vacuum on low. Our guide to why flocked trees shed and how to limit the mess has more ideas.

Lights, then decorations

On an unlit tree, string the lights after fluffing and before any ornaments. Working from the trunk outward keeps the wires hidden, and the pre-lit or unlit guide explains when stringing your own makes sense.

Keep the box and any bags the sections came in. You will want them again in January, and the guide to storing a flocked tree covers packing it without crushing the tips.

Still choosing? Our flocked tree buying guide compares all six, and the top pick section explains why Best Choice Products leads. The Best Choice Products review covers its setup in more detail.

If you want the simplest full-size setup

The Best Choice Products 7.5 ft tree has hinged branches, a three-step assembly and 550 LEDs already strung. It still sheds during setup like every flocked tree, and owners report that lights can stop working.

Questions and answers

More questions about setting up a flocked tree

How long does it take to fluff a flocked Christmas tree?

National Tree Company says about 30 minutes for its Acacia Slim and 45 to 60 minutes for the Wintry Pine. Fuller trees with more branch tips usually take longer, so plan an unhurried hour.

Should I fluff a flocked tree from the top or the bottom?

From the bottom up. The lower tiers are the widest and the easiest to reach before the upper sections hang over them, and you can then match the top to them.

How do I stop flocking from getting everywhere during setup?

Lay an old sheet under the tree, wear gloves and long sleeves, and handle the tips gently. Most shedding happens during setup, and a vacuum on low with the beater bar off clears the rest.

Why does my flocked tree have gaps after fluffing?

Usually because tips were left folded or all pointing the same way. Re-bend the neighboring tips across the gap, turn the thin side toward a wall, and fill any stubborn hole with an ornament or a pick.

Should I test a pre-lit tree before fluffing it?

Yes. Plug it in once the sections are joined. Several pre-lit trees draw owner reports of sections that stop working, and that is far easier to deal with before you shape every branch.